With the advancement of aquaculture automation, intelligent feeding robots have become critical for precise feed distribution, operational efficiency, and resource management. Their power drive and control systems, serving as the core of motion and actuation, directly determine the robot's operational endurance, torque response, power efficiency, and reliability in harsh environments. The power MOSFET, as a key switching component, significantly impacts system performance, thermal management, electromagnetic compatibility, and longevity through its selection. Addressing the demands of multi-motor control, frequent start-stop cycles, and operation in humid, corrosive environments, this article proposes a complete, actionable power MOSFET selection and design implementation plan with a scenario-oriented approach.

I. Overall Selection Principles: System Compatibility and Balanced Design

Selection should achieve a balance among electrical performance, thermal robustness, package suitability, and environmental reliability, tailored to the system's voltage buses (commonly 12V, 24V, or 48V in mobile platforms).

Voltage & Current Margin: Select MOSFETs with a voltage rating ≥50% above the maximum system voltage to handle motor back-EMF and transients. The continuous operating current should not exceed 60-70% of the device rating.

Low Loss Priority: Focus on low on-resistance (Rds(on)) to minimize conduction loss in motor drives. For switching frequency optimization in PWM controls, consider gate charge (Q_g) and output capacitance (Coss).

Package & Environmental Robustness: Prioritize packages with low thermal resistance and good power dissipation (e.g., DFN) for high-power stages. For harsh, humid environments, ensure devices have good corrosion resistance and consider conformal coating. Reliability under vibration and temperature swings is critical.

Reliability & Durability: Devices must withstand long duty cycles, high humidity, and potential salt spray exposure. Parameter stability over temperature and high ESD/surge immunity are essential.

图1: 水产养殖投饵机器人方案与适用功率器件型号分析推荐VBGQF1610与VBQF2311与VBI1695产品应用拓扑图_en_01_total

II. Scenario-Specific MOSFET Selection Strategies

Primary loads in feeding robots include propulsion/thruster drives, feeder mechanism actuators, and auxiliary sensor/control modules.

Scenario 1: Main Propulsion / Thruster Motor Drive (50W-150W)

Brushless DC (BLDC) or brushed DC motors for propulsion require high current handling, robust thermal performance, and high efficiency for extended runtime.

Recommended Model: VBGQF1610 (Single N-MOS, 60V, 35A, DFN8(3x3))

Parameter Advantages:

Utilizes SGT technology with very low Rds(on) of 11.5 mΩ (@10V), minimizing conduction losses.

60V rating offers ample margin for 24V systems. 35A continuous current handles startup and stall currents.

DFN8 package provides low thermal resistance (RthJA typically ~40°C/W) and low parasitic inductance for clean switching.

Scenario Value:

Enables efficient PWM motor control (>20kHz) for smooth speed variation and torque control.

High efficiency reduces heat generation, crucial for enclosed or waterproof compartments.

Design Notes:

Use with dedicated motor driver ICs featuring current sensing and protection.

Implement a large PCB copper pour (≥300 mm²) with thermal vias under the DFN thermal pad.

Scenario 2: Feeder Mechanism Actuator & Auxiliary Motor Control (10W-50W)

Smaller motors for gate valves, conveyor belts, or dispenser mechanisms require compact, efficient switches capable of frequent cycling.

Recommended Model: VBI1695 (Single N-MOS, 60V, 5.5A, SOT89)

Parameter Advantages:

Balanced Rds(on) (76 mΩ @10V) and current rating suitable for moderate-power auxiliary motors.

SOT89 package offers a good compromise between size, current capability, and PCB-based heat dissipation.

图2: 水产养殖投饵机器人方案与适用功率器件型号分析推荐VBGQF1610与VBQF2311与VBI1695产品应用拓扑图_en_02_propulsion

60V rating ensures robustness on 24V systems.

Scenario Value:

Ideal for direct drive by microcontrollers (3.3V/5V logic) via a gate resistor for on/off or low-frequency PWM control of feeder mechanisms.

Can be used for power distribution switching to enable sleep modes and reduce standby power.

Design Notes:

Add a gate resistor (10Ω-47Ω) to limit inrush current and damp ringing.

Ensure local copper pours for heat sinking on the PCB.

Scenario 3: High-Side Power Switching & Load Isolation

Critical for module power management, safety shutdown, and controlling loads where one side is grounded (e.g., sensors, solenoids, lighting).

Recommended Model: VBQF2311 (Single P-MOS, -30V, -30A, DFN8(3x3))

Parameter Advantages:

Very low Rds(on) of 9 mΩ (@10V) for a P-MOS, minimizing voltage drop in high-current power paths.

High current rating (-30A) suitable for main power branch switching or high-power auxiliary loads.

DFN8 package ensures excellent thermal performance for a high-side switch.

Scenario Value:

Enables safe disconnection of entire sub-systems (e.g., feeder, sensors) during faults or maintenance.

Useful for battery-connected loads without breaking the ground connection.

图3: 水产养殖投饵机器人方案与适用功率器件型号分析推荐VBGQF1610与VBQF2311与VBI1695产品应用拓扑图_en_03_feeder

Design Notes:

Requires a level-shifting circuit (e.g., N-MOS + resistor) for control from low-voltage logic.

Integrate current monitoring or fusing on the switched path for protection.

III. Key Implementation Points for System Design

Drive Circuit Optimization:

For VBGQF1610, use a dedicated gate driver IC (≥1A sink/source) to ensure fast switching and prevent shoot-through.

For VBI1695, an MCU GPIO with series resistor is often sufficient; add a pull-down resistor to ensure off-state.

For VBQF2311, implement a robust level-shifter with proper pull-up to Vcc to ensure full turn-off.

Thermal Management & Environmental Protection:

Employ tiered heat sinking: large copper areas + thermal vias for DFN packages; local copper for SOT packages.

In humid environments, apply conformal coating to the PCB, ensuring it doesn't interfere with thermal pads. Consider potting for critical modules.

Derate current usage if ambient temperatures consistently exceed 40-50°C.

EMC & Reliability Enhancement:

Use RC snubbers or small capacitors across motor terminals to suppress voltage spikes.

Implement TVS diodes on motor driver outputs and power inputs for surge suppression.

Include redundant mechanical and electronic fail-safes (e.g., watchdog timers, independent disable circuits) for critical drives.

IV. Solution Value and Expansion Recommendations

Core Value:

图4: 水产养殖投饵机器人方案与适用功率器件型号分析推荐VBGQF1610与VBQF2311与VBI1695产品应用拓扑图_en_04_management

High Efficiency & Extended Runtime: Low Rds(on) devices minimize energy waste, maximizing battery life for remote or solar-charged operations.

Robustness in Harsh Conditions: Selected packages and voltage margins ensure reliable operation despite vibration, humidity, and temperature variations.

System Safety & Control: Isolated high-side switching allows for safe power management and fault containment.

Optimization Recommendations:

Higher Power: For propulsion >150W, parallel multiple VBGQF1610s or select higher-current 60V/100V class MOSFETs.

Higher Integration: For complex multi-motor control, consider pre-driver ICs or integrated motor driver modules.

Extreme Environments: For direct saltwater exposure risk, specify automotive-grade (AEC-Q101) MOSFETs and employ enhanced sealing strategies.

Sensing Integration: Combine MOSFET drives with accurate current-sense amplifiers for load monitoring and predictive maintenance.

The selection of power MOSFETs is foundational to building durable, efficient, and intelligent feeding robots for aquaculture. The scenario-based selection—utilizing the high-power VBGQF1610 for propulsion, the versatile VBI1695 for actuators, and the robust VBQF2311 for power management—provides a balanced approach to performance and reliability. As technology evolves, the integration of advanced diagnostics and wider bandgap semiconductors (like GaN for ultra-high efficiency) will further enhance the capabilities of autonomous aquaculture systems. Solid hardware design remains the cornerstone of operational success in demanding agricultural and marine applications.